A central kitchen in Singapore starts with the premises, not the equipment. The site must be in a designated food zone or an approved food factory, the layout must follow SFA licensing conditions, and equipment must be chosen for cleanability, capacity and energy use before it is ordered. Planning these three items in that order avoids rework. Equipment that is energy-efficient from the start may also qualify for government grant support, and we guide food businesses through that process.
TL;DR
- Central kitchens must generally be in designated food zones or approved food factories. MSE stated in February 2026 that they are not allowed in shophouses.
- Central kitchens fall under Category 1 of SFA’s SAFE framework. Category 1 establishments seeking Grade A need a Food Safety Management System and an Advanced Food Hygiene Officer.
- Plan the layout by zone: receiving, storage, preparation, cooking, packing and cleaning, with separated raw and finished product areas.
- Choose equipment with smooth, non-porous, corrosion-resistant, cleanable surfaces, and plan hoods and flues for every cooking or frying line.
- Energy-efficient equipment may be eligible for the Energy Efficiency Grant, with up to 70% support for eligible SMEs.
Table of Contents
- What a central kitchen is, and who this guide is for
- Step 1: Choose premises that can be licensed
- Step 2: Understand the licensing and SAFE framework
- Step 3: Plan the layout by zone
- Step 4: Select and size equipment
- Step 5: Plan ventilation, fire safety and utilities
- Step 6: Build energy efficiency into the plan
- Our perspective
- Equipment for your central kitchen, from one supplier
- A setup sequence to follow
- FAQ
- Sources
What a central kitchen is, and who this guide is for
A central kitchen prepares or cooks food in volume for other outlets, caterers, delivery channels or institutions. The food is then packed and dispatched, instead of being served on site. Restaurant groups that open a second or third outlet, caterers that have outgrown a single kitchen, and food manufacturers moving into ready-to-eat products all end up planning one.
The rules are stricter than for a single restaurant kitchen, because larger-scale preparation carries a higher food-safety risk. The sections below follow the order in which a project is normally decided: premises, licensing, layout, equipment, services and energy.

Step 1: Choose premises that can be licensed
Premises decide whether the project can proceed at all. According to the Ministry of Sustainability and the Environment, central kitchens must generally be in designated food zones or approved food factories with the infrastructure to support food processing. The same reply states that central kitchens are not allowed in shophouses, and that they are subject to more frequent SFA inspections based on food-safety risk and track record.
Before signing a lease or a takeover, confirm the following in writing with the landlord or managing agent:
- The unit is in a designated food zone or an approved food factory.
- The unit is suitable for the type of food processing planned, including cooking and frying.
- Extraction can be installed and discharged in a way that suits the building (see the ventilation section below).
- Floor loading, power supply, water supply and drainage can support the equipment list.
- Loading and receiving access is available for delivery vehicles.
A unit that already has a food-factory use is not automatically ready for your menu. A kitchen built for cold preparation will not carry a frying and steaming line without new extraction, drainage and power. List your intended production first, then test the unit against it.
Step 2: Understand the licensing and SAFE framework
SFA’s conditions of licensing for food establishments set out infrastructure and premises requirements. SFA’s own licensing document is written so that operators can use it when designing premises before operation, and it warns that early compliance avoids costly remedial work. Read it before the layout is drawn, not after.
A second layer is the SAFE framework (Safety Assurance for Food Establishments). Its first phase took effect on 19 January 2026, and central kitchens are categorised as Category 1 establishments because of their larger-scale processing or preparation. In the same 4 February 2026 reply, MSE explains that a Category 1 establishment seeking Grade A must implement a Food Safety Management System and appoint an Advanced Food Hygiene Officer. Other establishments do not need to meet these additional conditions to receive grades.
In practical terms:
- Decide early whether the kitchen is aiming for Grade A.
- If so, budget time and staff for the Food Safety Management System and the Advanced Food Hygiene Officer role.
- Design record-keeping points, such as temperature logging and cleaning schedules, into the workflow instead of adding them later.
Food safety also starts at the receiving dock. Where fresh produce is a major input, written incoming-goods specifications help staff accept or reject deliveries consistently. Understanding premium fruit grades and tolerances is one example of defining what a compliant delivery looks like.
Step 3: Plan the layout by zone
The workflow of a central kitchen runs in one direction: goods in, storage, preparation, cooking, cooling, packing, dispatch. Cleaning and waste run alongside without crossing the food path. SFA’s licensing conditions give the layout rules that matter most:
- Provide clearly separated and labelled storage for raw materials, finished products, chilled and frozen products, packaging materials and cleaning equipment.
- Keep non-essential traffic out of processing and packing areas.
- Avoid a direct opening from the processing area to the outdoors.
- Provide equipment and surfaces that can be cleaned effectively.
The table below converts these rules into a planning checklist.
| Zone | What it needs | Planning point |
|---|---|---|
| Receiving | Space to check and unpack deliveries | Keep it apart from finished product |
| Dry and packaging storage | Racks, labelled areas | Separate from cleaning equipment |
| Chilled and frozen storage | Chillers and freezers sized to batch volume | Place near receiving and preparation |
| Preparation | Worktables, sinks, mixers | Separate raw from ready-to-eat handling |
| Cooking | Fryers, ovens, induction cookers, boilers | Hood and flue over every cooking or frying range |
| Cooling and packing | Blast or rapid cooling, packing tables, warmers | Limit access to authorised staff |
| Cleaning and waste | Sinks, racks, waste handling | Route away from the finished product path |
Two habits save money at this stage. First, draw the floor plan around the longest process, usually the one with the most steps, such as a cooked, cooled and portioned dish. Second, leave working clearance around each machine so that staff can clean behind and beside it. Our guides on cloud kitchen equipment layout and energy-efficient kitchen layouts cover zones, clearances and placement in more detail, and our interior design service for commercial kitchens is available for planning the space.
Step 4: Select and size equipment
Equipment selection answers three questions: what will be produced, how much per batch or per day, and which surfaces and machines can meet SFA’s cleanability conditions.
Hygiene requirements that apply to equipment
According to SFA’s licensing conditions for food processing:
- Product-contact surfaces must be food-inert, smooth, non-porous and corrosion-resistant.
- Surfaces must be accessible for cleaning, or be shown to be equivalent through clean-in-place treatment.
- Equipment should be self-emptying and self-draining, and protect contents from contamination.
- Removable items such as filters and screens must be open to inspection and cleaning.
Stainless steel tables, sinks, cabinets and racks are the usual choice for preparation and storage because they meet the smooth, non-porous, corrosion-resistant description. When comparing models, check that joints are easy to reach and that removable parts can be taken off without tools in a cleaning cycle.
Sizing for production
Size equipment to peak production, not average production. A practical method:
- List every product and its batch size.
- Note the cooking time and the number of batches needed in the production window.
- Divide the volume by the capacity of one unit, and add allowance for cleaning time.
- Check that cold storage holds at least one full day of raw material plus finished product awaiting dispatch.
The equipment types most central kitchens need are chillers and freezers, dough mixers and ovens, induction cookers, deep fryers, noodle and soup boilers, food warmers and steamers, stainless steel worktables and racks, and hot plates and grillers. These are the categories in our commercial kitchen equipment range. For budgeting across categories, see our equipment cost guide.
Step 5: Plan ventilation, fire safety and utilities
Cooking lines cause most of the services work in a central kitchen. SFA’s licensing conditions require cooking ranges where cooking or frying takes place to have a hood and flue with grease filters and an extractor fan. Extracted air must be discharged above the roof or away from neighbouring premises.
This means the cooking zone should be fixed early on the plan, because it determines the route of ducting to the discharge point. Confirm the following with the qualified designers and relevant authorities on the project:
- Electrical load for all equipment running at the same time.
- Gas supply if gas appliances are planned.
- Water supply and hot water capacity.
- Floor drainage and grease handling at the cooking and washing areas.
- Building and fire-safety approvals for the installed layout.
Our guides on kitchen ventilation requirements, SCDF kitchen fire safety and fryer filtration methods set out what operators should have ready for each.
Step 6: Build energy efficiency into the plan
A central kitchen runs long hours with refrigeration, heating and extraction in constant use, so energy is a large and continuing cost. NEA’s best practice guide for food manufacturing, published in March 2016, describes measures across plant design, retrofit, and operations and maintenance. It treats efficiency as something to include when designing new energy-consuming systems, and then to sustain through maintenance and operating practice. A new central kitchen is the point where this costs least, because no existing equipment has to be removed.
Owner-level actions that follow from this:
- Specify energy-efficient models for refrigeration, fryers, ovens and induction cookers at the purchase stage.
- Group heat-producing and cold-storage equipment apart from each other in the layout.
- Set a maintenance schedule for filters, door seals and burners from the first day.
- Record energy use per month, so that changes can be seen.
The Energy Efficiency Grant
The government’s Energy Efficiency Grant (EEG) on GoBusiness states that eligible SMEs may receive up to 70% support and non-SMEs up to 30%. The grant is subject to the lower of the applicable support level and a calculation based on expected lifetime energy savings. GoBusiness also lists Base Tier support of up to S$30,000 and notes that an extension to 31 March 2028 has been announced. Scheme periods, tiers and eligible equipment change, so check the GoBusiness page for the current terms before submitting an application.
Grant applications are normally made before purchase, so equipment should not be ordered until eligibility is confirmed. We provide guidance on claiming these grants for the equipment we sell. See also our article on kitchen retrofits and the EEG and our note on reducing commercial oven energy use.
Our perspective
Most central kitchen projects we see discussed begin with the equipment list and finish with the premises. The order should be reversed. Once the unit is confirmed and the zones are drawn, the equipment list becomes shorter and more accurate, and each item has a defined place.
Energy efficiency belongs in that same early decision. Our range is built around energy-efficient commercial kitchen equipment, and the products are designed to let food businesses claim grants of up to 70% of the original cost and reduce electricity bills. Our own claim is savings of up to 40% on electricity. A kitchen that specifies efficient refrigerators, fryers and induction cookers at the start does not need to retrofit them later.
We recommend that owners visit the showroom with their zone plan in hand. Seeing the machines at full size makes clearances, heights and cleaning access easy to judge before an order is placed.
David
Equipment for your central kitchen, from one supplier
Superior Kitchen Equipment supplies commercial kitchen appliances to restaurants, caterers, food manufacturers and new food businesses in Singapore. The range includes refrigerators, chillers and freezers, dough mixers and ovens, induction cookers, deep fryers, noodle and soup boilers, food warmers and steamers, stainless steel tables, sinks, cabinets and racks, and hot plates and grillers. Our energy-efficient products are suited to grant claims, and we give guidance on the claiming process.
Browse the full equipment collections, or visit the showroom to see the products before you finalise your layout.
A setup sequence to follow
- Define the products, daily volumes and dispatch method.
- Select premises in a designated food zone or an approved food factory.
- Read SFA’s licensing conditions and decide whether to aim for Grade A under SAFE.
- Draw the zone layout with separated raw, finished, chilled, frozen, packaging and cleaning areas.
- Compile the equipment list by zone and size it to peak production.
- Confirm electrical, gas, water, drainage, extraction and fire-safety needs with qualified designers.
- Check grant eligibility before ordering equipment.
- Order, install and commission, then train staff on cleaning and record-keeping.
FAQ
Can a central kitchen be set up in a shophouse?
No. MSE stated in February 2026 that central kitchens are not allowed in shophouses. They must generally be in designated food zones or approved food factories with the infrastructure for food processing.
What grade and requirements apply to a central kitchen under SAFE?
Central kitchens are classed as Category 1 establishments under the SAFE framework, whose first phase took effect on 19 January 2026. A Category 1 establishment seeking Grade A must implement a Food Safety Management System and appoint an Advanced Food Hygiene Officer.
What ventilation does a central kitchen need?
SFA’s licensing conditions require a hood and flue with grease filters and an extractor fan over cooking ranges where cooking or frying is carried out. Extracted air must be discharged above the roof or away from neighbouring premises. Confirm the detailed design with your qualified designers.
Can the cost of energy-efficient equipment be supported by a grant?
The Energy Efficiency Grant offers eligible SMEs up to 70% support and non-SMEs up to 30%, subject to a calculation based on expected lifetime energy savings. Check the GoBusiness page for the current terms, and confirm eligibility before purchase.
Sources
- Written Reply to Parliamentary Question on Licensing Criteria for Central Kitchens, MSE
- Oral Reply to Parliamentary Question on the new SAFE framework, MSE
- Conditions of Licensing for Food Establishments, SFA
- Energy Efficiency Grant, GoBusiness
- Best Practice Guide for Improving Energy Efficiency of Food Manufacturing, NEA
